Furnace & heating
Heat pumps
Ductless mini splits
GoodmanSeasonal tune-up and full diagnostic on your Carrier, Trane, or Goodman system - readings shown to you before any repair is proposed
Diagnosis first, numbers second - you approve the repair price before a single part goes in.
Get your free estimateStyles & brands we work with
See the difference
Before
After
Before
After
Before
AfterHow Much Does Furnace Replacement Cost in Dallas?
A full furnace replacement in Dallas typically costs between $4,200 and $8,900 for a standard single-family home in 2026, with mid-efficiency units starting around $4,200 and high-efficiency, two-stage systems running $6,500 to $8,900 installed. Your final price depends on the furnace size (BTU output), efficiency rating (AFUE), brand, and how much ductwork or venting modification the job requires. Most Dallas homeowners land in the $5,000 to $7,000 range for a properly sized, professionally installed system with a new thermostat.
That’s the honest answer up front. Below we break down exactly where that money goes, what drives the price higher or lower, and how to avoid overpaying in the Dallas market.
Furnace Replacement Cost Breakdown (2026)
Here are the line-item costs you’ll see on a furnace replacement quote in Dallas. These reflect current 2026 pricing from supply houses in the DFW metro and the labor rates of licensed HVAC contractors operating in the area.
| Cost Item | Typical Dallas Range | Notes |
|---|---|---|
| Furnace unit (80% AFUE, single-stage) | $1,800 – $2,800 | Goodman, Rheem, or equivalent entry-level unit |
| Furnace unit (96% AFUE, two-stage) | $3,200 – $5,200 | Carrier, Trane, Lennox, Daikin, Bryant, or American Standard |
| Labor and installation | $1,400 – $2,600 | Includes removal of old unit, gas line hookup, flue connection |
| Sheet metal / plenum adaptation | $300 – $750 | Higher if the new furnace footprint differs from the old |
| New thermostat | $150 – $400 | Smart thermostats run $250 – $400 installed |
| Permit and inspection | $75 – $250 | Required by the City of Dallas for gas furnace work |
| Code-required upgrades (venting, gas line) | $0 – $1,200 | Older homes in East Dallas, Oak Cliff, and Lake Highlands frequently need venting brought to current code |
The gap between a $4,200 job and an $8,900 job usually comes down to three things: the efficiency rating you choose, whether you go single-stage or two-stage, and what condition your existing flue and gas line are in. A furnace swap in a 1990s home in Richardson with a direct vent already in place is a straightforward half-day job. The same swap in a 1950s home in Casa View with an old masonry chimney liner that no longer meets code can add a thousand dollars in venting work alone.
What Affects Furnace Replacement Pricing in Dallas
- Furnace size (BTU rating). A 60,000 BTU furnace is plenty for a 1,400-square-foot home in Irving, but a 3,200-square-foot two-story in Plano or Frisco might need 100,000 BTU or more. Bigger units cost more, and so does the labor to fit them.
- Efficiency rating (AFUE). An 80% AFUE furnace is the cheapest to install but costs more to run. A 96% AFUE unit costs $1,500 to $2,500 more up front and typically saves Dallas homeowners $180 to $320 per year on gas, based on current Atmos Energy rates. Over a 15-year lifespan, the high-efficiency unit usually wins.
- Single-stage vs. two-stage vs. modulating. Single-stage is either full-on or off. Two-stage runs at about 65% capacity most of the time, which evens out temperatures and reduces short-cycling. Modulating systems adjust output in small increments and can add $2,000 to $3,500 to the total. In Dallas, where winter temperatures swing from 25 degrees one night to 65 the next afternoon, two-stage is the sweet spot for most homes.
- Access and existing setup. An attic furnace in a single-story home in Garland is easier to replace than a furnace crammed into a closet in a 1970s condo near White Rock Lake. Tight access means more labor hours. If the old unit is an 80% furnace that vents into a chimney and you’re upgrading to a 96% unit, the contractor has to run new PVC venting to an exterior wall, which adds $400 to $900.
- Brand and parts availability. Carrier, Trane, and Lennox carry a premium over Goodman and Rheem, but the installed price also reflects warranty terms and how quickly parts are available in the DFW supply chain. Dalton Heating & Air is factory-trained on all nine major residential brands: Carrier, Trane, Lennox, Goodman, Rheem, York, Daikin, Bryant, and American Standard. That matters because the same furnace can cost $300 to $600 more or less depending on which distributor a contractor buys from and whether they pass the savings through.
- Permits and code compliance. The City of Dallas requires a mechanical permit for furnace replacement. Some contractors quote without the permit and add it later, which is exactly the kind of door-price shift that leaves homeowners frustrated. A written price from Dalton Heating & Air includes the permit, the inspection, and every line item. The number you approve is the number you pay, period.
Is It Cheaper to Repair or Replace a Furnace in Dallas?
The short answer: if the repair cost is more than 30% of a new system’s price, replacement usually makes more sense. Most furnace repairs in Dallas run $150 to $700, with heat exchangers and blower motors at the top of that range. A heat exchanger replacement on a 15-year-old furnace can run $1,800 to $2,600, and once you’re in that territory with an aging system, you’re better off putting that money into a new unit with a fresh warranty.
Here’s the rule of thumb that saves Dallas homeowners money: if your furnace is over 15 years old and the repair estimate is over $900, get a replacement quote before you commit. Compare the two numbers. A new furnace at $5,200 with a 10-year parts warranty often beats a $1,400 repair on a unit that will likely need another $700 repair within 18 months.
We tell customers in North Dallas, Addison, and Farmers Branch the same thing every winter: don’t pay for a repair that extends the life of a furnace that’s already past its expected service life. Get both numbers. Then choose with the full picture.
How to Save on Furnace Replacement in Dallas
Furnace replacement is a big purchase, but there are ways to keep the total down without cutting corners that matter. Here’s what actually works in the Dallas market:
- Schedule replacement in the shoulder season. March through May and September through October are slower for HVAC contractors in Dallas. You may get better scheduling flexibility and occasionally a distributor rebate that contractors can pass through. Peak demand hits in December and January, when every furnace in the metro decides to fail at once.
- Right-size the furnace, don’t oversize it. An oversized furnace costs more up front and short-cycles, which means more wear and uneven heating. A proper Manual J load calculation is included with a Dalton Heating & Air replacement. If a contractor quotes you a bigger furnace than your current one without doing a load calculation, get a second opinion.
- Bundle the AC and furnace. If your central air conditioner is also aging, replacing both at once saves on labor and sheet metal work. A full HVAC system replacement in Dallas runs $7,800 to $13,500 for both units, which is less than doing them separately two years apart.
- Check for utility rebates. Atmos Energy and Oncor occasionally run rebate programs for high-efficiency furnaces. These rebates change year to year, so ask the contractor to check current offers when you get your quote.
- Get a written, itemized quote before you decide. This isn’t a savings tip so much as a protection tip. A written price locks the number. Dalton Heating & Air puts every price in writing before any work starts, on every job, without exception. Free estimates mean you can call (254) 280-5320, get a real number, and compare it against other written quotes with no obligation.
Furnace Replacement: What to Expect Step by Step
If you’ve never replaced a furnace before, here’s the process as it should work when you hire a contractor bound to The Garrison Standard:
- The load calculation and home assessment. A technician measures square footage, checks insulation levels, inspects existing ductwork, and tests airflow at each register. This determines the correct furnace size. Skip any contractor who quotes over the phone without seeing the home.
- Written quote with line-item pricing. You receive a document listing the furnace model, efficiency rating, labor, sheet metal work, permit fee, and any code-required upgrades. The price is in writing before any work starts. No exceptions.
- Permit and scheduling. The contractor files the mechanical permit with the City of Dallas and schedules the installation, typically a half-day to one full day for a standard replacement.
- Removal and installation. The old furnace is disconnected, removed, and the new unit is set in place. Gas line connections are pressure-tested, venting is installed to code, and the plenum is sealed and insulated. The site is cleaned before the crew leaves. Dalton Heating & Air crews leave the space as clean as they found it, every time.
- Startup, testing, and walkthrough. The technician runs the furnace through a full cycle, checks gas pressure, measures temperature rise across the heat exchanger, and verifies the thermostat is calling correctly. You get a walkthrough of the new system and the warranty documents.
- Final inspection. The City of Dallas inspector verifies the installation meets mechanical and gas code. The permit is closed out.
Every Dalton Heating & Air replacement includes a written guarantee. If the install isn’t right, we make it right. The 365-Day Done Right Promise covers a full year: if the work fails in that window, we come back at no charge.
Furnace Brands We Install and Their Dallas Price Ranges
Brand matters less than installation quality, but it affects price and warranty. Here’s what you can expect in Dallas by brand tier:
Goodman and Rheem: These are the workhorses. Entry-level 80% AFUE units installed start around $4,200, and 96% AFUE two-stage systems land in the $4,800 to $6,500 range. Good parts availability and solid warranties keep these popular in the Dallas rental market and for budget-conscious replacements.
Carrier, Bryant, and American Standard: Mid-premium tier. You’re paying for tighter manufacturing tolerances, quieter operation, and longer heat exchanger warranties. Installed prices run $5,500 to $7,800 for 96% AFUE two-stage systems in Dallas.
Trane, Lennox, and Daikin: Premium tier. Top-shelf filtration options, modulating burners, and the quietest operation in the industry. Installed prices start around $6,500 and can hit $9,000 or more for a fully modulating system with a communicating thermostat.
York falls somewhere between Goodman and Carrier on price in the Dallas supply chain, typically $4,800 to $6,800 installed for a high-efficiency unit. Dalton Heating & Air is factory-trained on all nine of these brands, which means the recommendation you get is based on your home and your budget, not on whatever brand the company happens to have in the warehouse.
How Long Does a Furnace Replacement Take in Dallas?
A standard furnace swap takes 4 to 8 hours. If new venting, gas line work, or sheet metal adaptation is required, expect a full day and occasionally a second half-day for the final inspection. From the time you approve the written quote, most Dallas replacements are scheduled within 3 to 10 days, depending on the season. During a December cold snap, every contractor in the metro is booked solid, which is another reason to handle replacement before the furnace fails entirely.
Dalton Heating & Air answers calls live 24/7. If your furnace dies in January, you’ll talk to a real person, not a voicemail queue. The Garrison Code requires every Dalton location to arrive inside the stated window, put the price in writing before starting, do the job by the book, and leave the site clean. When you schedule a replacement, you know who is coming before they arrive: background-checked, uniformed technicians, not a subcontracted crew you’ve never heard of.
Dallas-Specific Furnace Considerations
Dallas winters are mild compared to the Midwest, but that doesn’t mean the furnace is an afterthought. A few things we see regularly in this market:
Supply runs across hot attics. Many Dallas homes, especially those built in the 1980s and 1990s in Mesquite, Garland, and Richardson, run supply ducts through unconditioned attics. In summer those ducts soak up heat; in winter they lose it. A new high-efficiency furnace can’t fix leaky or uninsulated ducts. If your ducts are in poor shape, sealing and insulating them is a $600 to $1,500 add-on that pays for itself in efficiency.
Foundation movement and settling. The clay soils in DFW shift dramatically with moisture swings, which can crack ductwork under slab foundations. Homes in East Dallas and Oak Cliff with slab ducts sometimes need a section replaced or re-routed before a new furnace will perform properly. A good load assessment catches this before the install, not after.
Gas line capacity. Older homes in neighborhoods like Lakewood and M Streets sometimes have half-inch gas lines that were fine for an 80,000 BTU furnace but undersized for a larger unit. If you’re upsizing the furnace, the contractor should verify the gas line can deliver the needed volume. A gas line upgrade runs $500 to $1,100 depending on the run length.
Attic and closet installations. A lot of Dallas gas furnaces are installed in hallway closets. Newer high-efficiency units are slightly larger than their 1980s predecessors due to the secondary heat exchanger, so some closet swaps require modifying the return plenum to fit. That’s a $250 to $600 sheet metal adjustment.
Our Furnace Replacement in Dallas page walks through the full installation process and what to look for in a contractor. For more on our broader services, start at the home page.
FAQs – Furnace Replacement Cost
How much does a furnace replacement cost in Dallas in 2026?
A furnace replacement in Dallas typically costs $4,200 to $8,900, with most homeowners paying between $5,000 and $7,000 for a mid-efficiency two-stage system installed by a licensed contractor. The final number depends on furnace size, efficiency rating, brand, and any venting or gas line work the home requires. For an exact quote, call Dalton Heating & Air Dallas at (254) 280-5320 for a free written estimate.
Is it cheaper to repair or replace a furnace?
It’s usually cheaper to repair if the furnace is under 12 years old and the repair is under $700. It’s usually smarter to replace if the furnace is 15 years or older and the repair exceeds $900, or if the heat exchanger has failed. A heat exchanger replacement alone runs $1,800 to $2,600 in Dallas, which is a significant fraction of a new unit’s price. We show you both numbers and let you decide with the full picture. Call (254) 280-5320 for an honest assessment and a written quote for each option.
How much does a high-efficiency furnace cost in Dallas?
A 96% AFUE high-efficiency furnace costs $5,500 to $8,900 installed in Dallas, depending on whether it’s single-stage, two-stage, or modulating. The premium over an 80% AFUE unit is typically $1,500 to $2,500, but the gas savings over a 15-year life usually exceed the extra cost at current Atmos Energy rates. Rebates may reduce the total further. Call (254) 280-5320 for a written quote on your specific home size and setup.
Can you replace a furnace the same day in Dallas?
In most cases, yes, but it depends on the season and the complexity of the install. During December and January, same-day replacement is difficult because every contractor in the DFW metro is at capacity. Outside peak season, a standard swap can often be scheduled within 24 to 72 hours. Dalton Heating & Air answers calls live 24/7. If your furnace has failed and you need it handled, call (254) 280-5320 and we’ll give you a real availability window, not a callback promise.
What size furnace do I need for a Dallas home?
For a Dallas home, the general starting point is 30 to 40 BTUs per square foot, but that’s a rough estimate. A 1,500-square-foot home typically needs a 60,000 BTU furnace, a 2,200-square-foot home needs about 80,000 BTU, and a 3,000-square-foot home needs 100,000 BTU or more. The only way to size a furnace correctly is a Manual J load calculation that accounts for insulation, window area, ceiling height, and duct leakage. A properly sized furnace costs less up front and runs more efficiently. Dalton Heating & Air includes a load calculation with every replacement quote. Call (254) 280-5320 to schedule a free assessment.
Get a Written Furnace Replacement Quote in Dallas
If you’re weighing a furnace replacement in Dallas, don’t guess at the price. Call Dalton Heating & Air Dallas at (254) 280-5320 and get a free, written, line-item quote with no obligation. The number you approve is the number you pay. Marco Benitez and his team have been serving Dallas homeowners under The Garrison Standard since 2003, and every replacement comes with a written guarantee, the 365-Day Done Right Promise, and a crew that shows up inside the window, does the job by the book, and leaves the site clean.
Get the real number. Then decide.
Pricing reflects the Dallas market as of 2026. Dalton Heating & Air Dallas offers free estimates – call (254) 280-5320.
Written by Marco Benitez, Owner at Dalton Heating & Air Dallas, serving Dallas since 2003.
What Our Customers Say
"No pressure to upgrade. He said the old unit had a few years left and fixed the actual problem."
- Jimmy V."Thermostat swapped for a programmable one and ducts checked for leaks. The house is more even now."
- Omar H."Honest, direct people. Told me what the furnace needed and nothing more, and the bill matched."
- Eliza S.